3 4 x 6 7 is a dimensionally labeled piece of rough-sawn lumber measuring 3 inches by 4 inches in cross-section and 6 feet 7 inches long, typically used in structural framing for walls, floors, and roof supports in residential construction.
This notation follows standard U.S. building practice where lumber sizes are given in nominal inches. The actual dimensions are smaller due to planing and drying processes. A 3×4 is not 3 inches by 4 inches in reality-it measures 2.5 inches by 3.5 inches after surfacing. The length, 6 feet 7 inches, is precise and commonly used for wall studs and joists in homes.
These pieces are usually made from softwood species like spruce-pine-fir (SPF) or Douglas fir. They are graded for strength and used in load-bearing applications. The 3×4 designation appears on material lists, blueprints, and supplier catalogs under the category of "dimensional lumber" or "framing lumber."
In residential framing, 3 4 x 6 7 refers to a structural member cut to specific dimensions for consistent fit and load distribution. These beams are used vertically as wall studs or horizontally as floor joists and rafters. Their standardized size ensures compatibility with other components like plywood sheathing, drywall, and insulation.
For example, a typical interior wall frame uses 3×4 studs spaced 16 inches on center. The 6'7" length allows for a standard ceiling height of 8 feet minus the thickness of the top and bottom plates. This leaves about 7 feet 11 inches of usable vertical space, which fits within the 6'7" stud length when accounting for plate thickness and framing tolerance.
When installing, builders mark the location of each stud using a chalk line or laser level. The 3×4 is then secured to the top and bottom plates with nails or screws. Fasteners are driven through the face of the stud into the plate, creating a rigid structure capable of supporting ceiling loads and resisting lateral forces during wind events.
While 3 4 x 6 7 is a common size, lumber comes in multiple nominal dimensions. The most frequently used sizes in framing include:
| Nominal Size | Actual Size (inches) | Common Use |
|---|---|---|
| 2×4 | 1.5 × 3.5 | Wall studs, floor joists, rafters |
| 2×6 | 1.5 × 5.5 | Load-bearing walls, longer spans |
| 3×4 | 2.5 × 3.5 | Interior partitions, non-load-bearing frames |
| 4×6 | 3.5 × 5.5 | Beams, headers, deck support posts |
Not all 3×4 lumber is used in primary structural roles. Some is repurposed for trim, shelving, or temporary bracing. The grade of the wood also matters-construction-grade lumber is stamped with a grade symbol (like "No. 2" or "Stud") indicating its strength and acceptable knots or defects.
Engineered alternatives like laminated veneer lumber (LVL) or oriented strand board (OSB) are sometimes substituted for solid wood in high-stress areas. However, 3 4 x 6 7 remains a staple in DIY and professional builds due to its availability, cost-effectiveness, and ease of handling.
3 4 x 6 7 is standard in single-family home construction, especially in regions with cold climates where energy efficiency and structural integrity are critical. Its size balances strength, weight, and material cost. A 3×4 stud weighs about 1.8 pounds per foot, making it manageable for one worker to carry and install.
For example, in a 2,400-square-foot house with 120 linear feet of interior walls, approximately 1,200 studs are needed. Using 3×4s at 16-inch spacing reduces material waste and simplifies layout. The 6'7" length avoids the need for field cutting in most cases, speeding up build time.
According to the National Association of Home Builders (NAHB), 83% of new single-family homes in the U.S. use 2×4 or 3×4 framing for interior walls. The consistency of nominal sizes enables prefabrication-walls are often built off-site and delivered ready-to-install, reducing on-site labor and errors.
Many people assume that "3 4 x 6 7" means exactly 3 inches by 4 inches by 6 feet 7 inches. This is incorrect. All nominal lumber sizes are reduced after surfacing. A 3×4 is actually 2.5×3.5 inches. This discrepancy exists because the original green lumber shrinks during drying and is planed to remove surface imperfections.
Another misunderstanding is that 3×4 lumber can support heavy loads. While it's strong enough for non-load-bearing partitions, it cannot replace 2×6 or 4×6 members in structural beams. Using a 3×4 as a header over a doorway leads to sagging and potential failure under live loads.
A key fact often missed: the length "6 7" is not rounded. A 6'7" piece is precisely 79 inches long. This exact measurement is chosen because it fits between standard floor joist spacing (typically 16" or 24" o.c.) and allows for proper alignment with wall plates. Standard lengths like 8', 9', and 10' are also available, but 6'7" is optimized for common room heights.
I once built a closet partition in my garage using 3×4s. I measured the space and cut four pieces to 6'7". When I installed them, they fit perfectly between the top and bottom plates. The gap was less than 1/8 inch, and the joints aligned cleanly. This precision is why contractors rely on nominal dimensions-they're predictable, repeatable, and compatible across projects.
3 4 x 6 7 is a standard dimensional lumber size used in residential construction. It refers to a 3×4 beam that is 6 feet 7 inches long, with actual dimensions of 2.5 inches by 3.5 inches and 79 inches in length. This size is widely used for framing interior walls and non-load-bearing structures due to its balance of strength, cost, and ease of installation.