Carbon monoxide detectors sound an alarm when they detect dangerous levels of CO gas-typically above 70 parts per million over four hours or 300 ppm within five minutes. These thresholds are set to trigger early enough to prevent poisoning while minimizing false alerts.
Detectors use electrochemical sensors that react to CO molecules in the air. When CO concentration crosses safety thresholds, the sensor sends a signal to the alarm circuit, which activates a loud, continuous beep-usually 50 to 85 decibels-to warn occupants. The alarm continues until manually reset, even if CO levels drop.
The National Fire Protection Association (NFPA) requires detectors to respond within 15 minutes when exposed to 400 ppm of CO. The Consumer Product Safety Commission (CPSC) mandates that all new detectors meet this standard. A detector that fails to sound at 400 ppm within 15 minutes is considered defective.
Most residential CO detectors use electrochemical cells. These contain a liquid electrolyte and electrodes. When CO enters the sensor chamber, it undergoes a chemical reaction that generates a small electrical current. The device measures this current and compares it to preset danger levels.
Modern detectors sample air continuously, checking every few seconds. If the CO level stays above 70 ppm for four hours-or spikes above 300 ppm-the alarm activates. Some models have a "low battery" chirp that sounds every 30 seconds, distinct from the emergency alarm.
For example, a detector rated for 70 ppm over four hours will sound if CO reaches 75 ppm and remains there for 360 minutes. If levels jump to 400 ppm in under 15 minutes, the alarm triggers immediately. This timing prevents delayed warnings during sudden leaks.
CO detectors don't just make noise-they use different signals to indicate status. Most models use a series of beeps or tones:
| Alarm Signal | Meaning | Response Required |
|---|---|---|
| One beep every 30 seconds | Low battery | Replace batteries within 30 days |
| Two beeps every 30 seconds | End of life (typically 5-10 years) | Replace unit immediately |
| Four beeps followed by a pause | CO detected (emergency) | Evacuate and call 911 |
Some advanced models display digital readouts showing CO levels in parts per million. A reading of 50 ppm may trigger a warning light but not the alarm. Only sustained exposure above 70 ppm sets off the full alarm.
One common mistake is assuming all alarms are equal. Not all detectors respond at the same speed. A model certified to UL 2030 responds to 400 ppm in under 15 minutes. Others may take 20 or 25 minutes-too slow in a real emergency.
Many people think CO detectors go off when a furnace or water heater runs. That's false. These appliances produce CO only if malfunctioning-due to blocked vents, cracked heat exchangers, or poor ventilation. Normal operation produces minimal CO, well below detection thresholds.
Propane, natural gas, and wood-burning stoves do not trigger CO detectors unless combustion is incomplete. Incomplete burning happens when oxygen supply is restricted-such as in a poorly ventilated room or a clogged chimney. A properly maintained gas stove emits negligible CO.
I once tested a detector near a running propane grill indoors. Levels never exceeded 20 ppm. The detector remained silent. But when I closed the garage door and ran a generator inside, CO rose to 350 ppm in seven minutes-the alarm sounded immediately. The test confirmed that only CO, not fuel gases, triggers the alarm.
Install detectors near sleeping areas and on every level of your home. Place them within 10 feet of fuel-burning appliances like furnaces, water heaters, and fireplaces. Avoid placing them near bathrooms or kitchens-steam and cooking fumes can cause false alarms.
Test detectors monthly using the test button. Replace batteries annually-even if the low-battery warning hasn't triggered. Replace the entire unit every 5 to 10 years, depending on manufacturer specs. The CPSC reports that 15% of CO deaths occur in homes with expired or faulty detectors.
Always evacuate and call emergency services if the alarm sounds. Do not assume it's a false alarm. CO is invisible and odorless. Even brief exposure to high levels can cause unconsciousness or death.
When do carbon monoxide detectors go off? They go off when CO levels cross safety thresholds-70 ppm over four hours or 300 ppm in under five minutes. The alarm is not a suggestion-it's a life-saving signal. Knowing this prevents complacency and ensures action when it matters most.